Can someone explain me why this happen

RudeGuy · Postby **RudeGuy** » Sun Oct 12, 2014 9:39 am

One time Valtteri made some SMB2 subspace graphics and one of them is an NPC. For some reason, when I want to use this NPC (which replace a mushroom block by the way) I can place it in the level editor, but it somehow is gone while I playtest my level. Why?

DimitrisPowerSeven · Postby **DimitrisPowerSeven** » Sun Oct 12, 2014 9:42 am

Maybe it disappear because is still like block,use noblockcollision=1 and nogravity=1,but still maybe.

Edit:400 posts yeeee!

RudeGuy · Postby **RudeGuy** » Sun Oct 12, 2014 10:15 am

DimitrisPowerSeven wrote:Maybe it disappear because is still like block,use noblockcollision=1 and nogravity=1,but still maybe.

Edit:400 posts yeeee!

I've checked and in the NPC code there are both 2 codes.

DarkShadeX · Postby **DarkShadeX** » Sun Oct 12, 2014 10:30 am

Christian07 wrote:
DimitrisPowerSeven wrote:Maybe it disappear because is still like block,use noblockcollision=1 and nogravity=1,but still maybe.

Edit:400 posts yeeee!
I've checked and in the NPC code there are both 2 codes.

Could you give me the GFX and NPC Code?

RudeGuy · Postby **RudeGuy** » Sun Oct 12, 2014 10:33 am

Darkchaox100 wrote: Could you give me the GFX and NPC Code?

https://www.mediafire.com/?masxgfcvhc8bq66

DarkShadeX · Postby **DarkShadeX** » Sun Oct 12, 2014 10:39 am

Works fine for me...
If it doesnt work for you,remove the width and height code from the NPC code (not the gfxheight/gfxwidth one)

h2643 · Postby **h2643** » Sun Oct 12, 2014 10:46 am

Maybe because it isn't set on "Friendly" and "Don't Move".

DarkShadeX · Postby **DarkShadeX** » Sun Oct 12, 2014 10:49 am

h2643 wrote:Maybe because it isn't set on "Friendly" and "Don't Move".

I didnt had to active Friendly and Dont Move.

RudeGuy · Postby **RudeGuy** » Sun Oct 12, 2014 10:57 am

Darkchaox100 wrote:If it doesnt work for you,remove the width and height code from the NPC code (not the gfxheight/gfxwidth one)

Didn't tought about it, I'll try doing that. Thanks for help.

h2643 · Postby **h2643** » Sun Oct 12, 2014 11:03 am

Well, sometimes it dissappeared for me when I tried to place the Subspace NPC into the level, but when I set it on "Friendly" (and "Don't Move"), it worked.

Flying Brick · Postby **Flying Brick** » Sun Oct 12, 2014 11:19 am

I've had this problem before, too. For me, it was caused by using 1x1 pixels in the NPC graphic, which made the NPC disappear as soon as I started the test. Ever since I stopped using those, I never had any problem again. Maybe that's your problem, I don't know

RudeGuy · Postby **RudeGuy** » Sun Oct 12, 2014 11:44 am

Flying Brick wrote:I've had this problem before, too. For me, it was caused by using 1x1 pixels in the NPC graphic, which made the NPC disappear as soon as I started the test. Ever since I stopped using those, I never had any problem again. Maybe that's your problem, I don't know

I don't think I have the same problem, as there aren't any 1x1 pixels. Anyways, I finally fixed the problem by changing the size of the NPC. there is a thing about his placement, though:

Spoiler: show

The place where the cursor is is the only place where I can select the NPC. Is there a reason for this?